Forklift

Lemcol Castors

Lemcol Wheels

Lemcol Conveyors

Fork Extensions

This page contains information about: Fork Spreaders | Hydraulic Reachforks | Fork Slippers

Fork Spreaders

Type FS2.5

Special

Type FS2.5 Fork Spreader

Safely pick up extra wide or flexible loads without the risk of damage to products such as plasterboard, roof sheeting, timber, plaster tubing etc. The Type FS fork spreader evenly distributes the load over the length of the attachment. The slip-on attachment is secured to the lift truck by a safety chain.

 

  • Capacity 2500kg at 600mm Load Centre
  • Width 3.0m x 1.2m
  • Unit Weight 225kg
  • Pocket Size 160 x 60mm
  • Pocket Centres 770mm

Type FS3-LG Fork Spreader

Safely pick up extra wide or flexible loads without the risk of damage to products such as plasterboard, roof sheeting, timber, plaster tubing etc. The Type FS fork spreader evenly distributes the load over the length of the attachment. The slip-on attachment is secured to the lift truck by a safety chain.

Specifications:

  • Capacity 3000kg at 600mm Load Centre
  • Width 3.0m x 1.2m
  • Unit Weight 300kg
  • Backrest Height 600mm
  • Pocket Size 160 x 60mm
  • Pocket Centres 770mm

Special

Special

Type FS3-LG

Special

Hydraulic Reachforks
Reachforks are hydraulically extendible and retractable forks, that save you time, space and money. Available from 2 tonne to 10.5 tonne capacity.

Reachforks allow "double-deep" stacking increasing warehouse capacity by up to 30% compared to "single-deep" warehouse operations. Accessibility is also improved compared with drive-in and live storage racking. The investment cost of racking and handling equipment is relatively low.


Trucks can be completed loaded and unloaded from one side. Turning the vehicle or driving around both sides of the trailer is no longer required. This saves time and space and also makes the operation much safer.
Reachforks can be extended to transport two pallets at a time. Where large volumes or long distances are involved this can offer considerable benefits.

Standard lengths -

  • Closed 1100mm Extended 1850mm
  • Closed 1200mm Extended 2050mm
  • Closed 1350mm Extended 2350mm

Model Capacity Kg on LC mm Section Length/Stroke Lost Load CoG1mm CoG2mm Mass Kg ISO/FEM
  600 1450 1750 D x S mm mm Thickness mm ± ± ±  
RG4 25 1100/0750         1100/0750   355 535 190  
RG4 25 1200/0850 2500 1035 850 170 x 55 1200/0850 45 395 605 200 ll
RG4 25 1350/1000         1350/1000   465 710 220  
RG4 35 1100/0750         1100/0750   355 515 215  
RG4 35 1200/0850 3500 1450 1200 170 x 63 1200/0850 52 400 585 230 ll / lll
RG4 35 1350/1000         1350/1000   465 687 250  
RG4 45 1100/0750         1100/0750   330 496 205  
RG4 45 1200/0850 4500 1850 1550 170 x 55 1200/0850 45 370 564 215 lll
RG4 45 1350/1000         1350/1000   435 670 235  
RG4 60 1100/0750         1100/0750   333 516 230  
RG4 60 1200/0850 600 2500 2050 170 x 65 1200/0850 52 375 590 245 lll
RG4 60 1350/1000         1350/1000   440 695 265  

Power Range Reachforks: two cylinders per fork, for reaching with load. Includes separate equaliser valve and four hydraulic hoses.

Model Capacity Kg on LC mm Section Length/Stroke Lost Load CoG1mm CoG2mm Mass Kg ISO/FEM
  600 1450 1750 D x S mm mm Thickness mm ± ± ±  
RE4 80 1100/0750         1100/0750   325 480 360  
RE4 80 1200/0850 8000 3300 2750 225 x 65 1200/0850 50 365 550 380 lV
RE4 80 1350/1000         1350/1000   430 350 430  
RE4 105 1100/0750         1100/0750   315 460 420  
RE4 105 1200/0850 10500 4300 3600 225 x 75 1200/0850 60 360 525 445 lV
RE4 105 1350/1000         1350/1000   420 620 480  

Thin Range Reachforks : two cylinders per fork, for reaching with load. Includes separate equaliser valve and four hydraulic hoses.

Model Capacity Kg on LC mm Section Length/Stroke Lost Load CoG1mm CoG2mm Mass Kg ISO/FEM
  600 1450 1750 D x S mm mm Thickness mm ± ± ±  
RE4 32 1100/0750         1100/0750   350 510 205  
RE4 32 1200/0850 3200 1325 1100 170 x 47 1200/0850 45 410 580 220 ll
RE4 32 1350/1000         1350/1000   480 680 240  

Power Range Reachforks : two cylinders per fork, for reaching with load. Includes integrated equaliser system.

Model Capacity Kg on LC mm Section Length/Stroke Lost Load CoG1mm CoG2mm Mass Kg ISO/FEM
  600 1450 1750 D x S mm mm Thickness mm ± ± ±  
RG2 20 1100/0750         1100/0750   370 540 160  
RG2 20 1200/0850 2000 825 685 140 x 55 1200/0850 45 415 610 170 ll
RG2 20 1350/1000         1350/1000   480 715 185  
RG2 28 1100/0750         1100/0750   355 515 215  
RG2 28 1200/0850 2800 1150 960 140 x 63 1200/0850 52 400 580 230 ll
RG2 28 1350/1000         1350/1000   465 685 250  

Extension Range Reachforks : one cylinder per fork, suitable for adapting fork length for different pallet sizes. Includes integrated equaliser system.

Model Capacity Kg on LC mm Section Length/Stroke Lost Load CoG1mm CoG2mm Mass Kg ISO/FEM
  600 D x S mm mm Thickness mm ± ± ±  
NG4 20 0800/0400 2000 140 x 55 0800/0400 45 240 325 135 ll
NG4 20 1000/0200 2000 140 x 55 1000/0200 45 325 365 150 ll
  • Minimum operating pressure 10 MPa, maximum 20 MPa.
  • Capacities shown are nominal.
  • Other capacities and dimensions on request.
  • The capacity shown applies to the forks and not the lift truck.
  • The lift truck manufacturer must determine the combines telescopic fork/truck capacity.

Fork Slippers

Fork Slippers Diagram

Designed for ease of operation with a slim profile to extend the versatility of your Lift Truck. These Slippers have been designed and manufactured in accordance with AS 2359.15. Standard finish on all type 'FE' Slippers is Zinc plated. Finish on all custom built Slippers is enamel painted colour Black.

Additional FEATURES:

  • Supplied with Locking Pins
  • Fitted with Rating Plate
  • Made of High Tensile Grade Steel
  • High Safe Working Load (SWL) Rating
  • Supplied with Instructions

In accordance with AS2359.15 Slippers used for general usage should be no longer than 167% of the supporting Tine's length. If the Slippers are longer than 167%, then the usage of those Slippers shall be restricted to their specified application.
Type
Length
mm
To Suit
max tine size
 Weight kg
(pair) 		Rated
(pair)
FE1-16
1600
100 X 45
50
 3000KG
FE1-18
1800
100 X 45
56
 SWL
FE1-21
2100
100 X 45
66
 at
FE1-24
2400
100 X 45
75
 600MM LC
FE2-16
1600
130 x 50
59
 4500kg
FE2-18
1800
130 X 50
66
 SWL
FE2-21
2100
130 x 50
77
 at
FE2-24
2400
130 X 50
88
 600mm LC
FE3-16
1600
150 x 55
91
 6500kg
FE3-18
1800
150 x 55
102
 SWL
FE3-21
2100
150 x 55
119
 at
FE3-24
2400
150 x 55
136
 600mm LC
FE3-30
3000
150 x 55
170
  
FE4-18 1800 155 x 65 133 8500kg
FE4-21
2100
155 x 65
155
 SWL
FE4-24
2400
155 x 65
177
 at
FE4-30
3000
155 x 65
221
 600mm LC
SL5-18
1800
Custom
170
 8000kg
SL5-21
2100
built
200
 SWL
SL5-24
2400
to
220
 at
SL5-30
3000
suit
280
 600mm LC
SL6-21
2100
Custom
380
 12000kg
SL6-24
2400
built
430
 SWL
SL6-30
3000
to
540
 at
SL6-35
3500
suit
630
 600mm LC
SL7-24
2400
Custom
520
 16000kg
SL7-30
3000
built to
650
 SWL at
SL7-35
3500
suit
760
 600mm LC

 

Enquiry Form

This is a short form you can submit to request information from Active Lifting:

Please provide the following contact information
Items marked with an * are required fields.

* Name
Title
Organisation
Street Address
Address (cont.)
City
State
Postal code
Country
Work Phone
FAX
* E-mail
Web Site
Please provide the following product information you are enquiring about if known:
Product name
Type
Enter any questions you have in the box below.
When you have completed the form, please press the Submit Form button below:

Google
www activelifting.com.au
^ Top ^
Materials Handling | Dangerous Goods | Lifting Equipment | Electronic | Safety | Architectural Fittings | Rud Lifting and Lashings
Home | Contact Us | | Links | Policy | Search | Secure Payments
PO Box 266, Stepney, South Australia 5069  Ph: +61 8 8362 4566   Fax: +61 8 8362 4766   Mob: 0414 347 404 
Copyright © 1999 Active Lifting Equipment Co. Pty Ltd.         Site Design & Maintenance by B & P THURSBY Digital Services